Contact Us

Double Sided Reflow Assembly

Double Sided Reflow Assembly

The board comes off the line finished on one side, and the order asks for parts on both. From that point the panel is flipped, printed again, placed again and sent through the oven a second time, and the joints made in the first pass go through reflow again with nothing holding them but surface tension.

Double sided reflow assembly is usually treated as the same job done twice. It is not. The second pass has a different thermal load, a different support problem, and a failure mode that only exists because a part is hanging under the board on its way through the oven.

What the second pass actually changes

Every joint on the first side melts again. That is normal and it is accounted for in the profile, but it means the first side cannot be inspected as final until the second pass is done, and it means any part already placed has to survive a second trip at peak temperature. Two passes are still inside most laminate and component ratings. A third is where the questions start, and the limits are set out in how many reflow cycles a board survives.

The thermal load is not only the board. The first side is now a set of bodies on the underside of the panel, and they pull heat out of the assembly at different rates. A zone of large inductors beside a zone of 0402 parts gives one panel two very different profiles, and the profile has to be set for the slower one without cooking the faster one.

What holds a part on the underside

MethodWhen it is usedWhat it costs
Surface tension onlyParts under roughly 0.5 g per joint, no tall body, no heavy inductorNothing, but the margin is set by part mass and pad area, not by preference
Adhesive dots between padsHeavy parts, cylindrical bodies, parts with few joints carrying a lot of massAn extra dispense step, a cure before the flip, and a dot that must not touch a pad
Partial cure of the pasteSmall parts that slump or slide during the flipA cure step in the middle of the line, and paste whose working life has to allow it
Mechanical supportConnectors, shields, anything bolted or clippedHardware on the BOM and a hand step that has to be planned as one

The choice is made per part, on mass and joint count, not on the size of the body. A 10 mm inductor with two large pads often holds better than a light 15 mm can with a single row, because the joint area that resists the drop is what matters.

Warpage, and why it is worse the second time

A panel that leaves the first pass slightly bowed goes into the second pass with that bow, plus the copper and the parts now on the other face. Support pins that worked on the first side no longer sit where the panel needs them, because the underside is populated. The stencil prints on a surface that is not flat, and the corner deposits come out thick while the middle comes out short.

The board limit we work to for assembly is 0.75 percent, and a panel near that limit on the first pass is a panel that will print badly on the second. Where a board is known to be asymmetric in copper, the fix is in support and in the print check, not in the profile.

Moisture: the second reflow is the one that pops

A part that survived the first pass has still absorbed nothing, if the handling was right. Where the panels wait between passes in a normal room, they do not, and the second pass becomes the one that drives moisture out of a package fast enough to crack it. Every panel between passes belongs in a dry store or under a controlled clock, and the parts on the underside are the ones with no rework path.

Baking, floor life and the bag opening time are tracked on the kit record, and the rule is on component MSL and bake control. A double sided build is where that record earns its place, because the gap between passes is the exposure nobody writes down.

Support and handling on the flip

On the second pass the panel is supported at its edges only, or on pins placed in areas the first side left free. Both have limits. Edge support lets the middle sag under a heavy part. Pins need a clear area on the populated side, and a pin under a tall body is a cracked part waiting to happen. Where neither works, the panel is run on a carrier.

The flip itself is a handling step. Parts on the underside are unsupported until they enter the oven, so the conveyor transfer between the printer and the placer is where a heavy part is most likely to move.

How SUPERB PCBA runs the second pass

The build runs across seven SMT lines with placement to 01005 (0.4 by 0.2 mm) at up to 40,000 CPH, and both passes run on the same line so the panel does not sit between processes. Paste is measured after each print with 3D SPI, which matters more on the second pass than the first, because the print is landing on a panel that is already loaded.

Reflow is a twelve zone nitrogen oven at under 500 ppm oxygen with a SAC305 profile, and the second pass profile is built and verified on the panel, not taken from the first pass. Verification follows the method on reflow profile verification, with thermocouples on the underside parts that carry the most mass.

After reflow the panel goes through 3D AOI and, where a joint sits under a body, X-ray in 2D or CT to IPC-7095. Electrical test follows, with in circuit or flying probe depending on access, and a functional test on tooling built for the product where the customer asks for one.

Questions buyers ask

Can every part go on the underside?

No. Mass per joint decides it, and a few part types are excluded by their own handling notes. The list is checked against the BOM before the build starts, not discovered at the placer.

Does the second pass affect the first side joints?

It melts them again, so the first side is inspected after the second pass rather than between passes. The joint that forms in the second pass is the one that ships.

Is adhesive always needed for heavy parts?

Only where surface tension cannot hold the mass through the flip and the oven. Adhesive adds a dispense and cure step, so it is chosen per part, and it is quoted as part of the process.

Next step

Send the BOM, the Gerber set and the assembly drawing, with a note on which parts the customer considers heavy or heat sensitive. The process note comes back with the holding method per part, the profile for both passes, and the inspection point for each side.