Four ounce copper changes two things at once and it is worth knowing both before the quote. In etch, the sidewall becomes a trapezoid: a line that finishes at 6 mil across the top is closer to 4 mil at the base unless the artwork carries compensation. In assembly, 140 micrometres of copper is a heat sink, so preheat, soak and time above liquidus all move, and solder mask over a heavy trace is thinner at the edge than the same mask over 1 oz.
The scale first. One ounce is 34.3 micrometres nominal, 1.35 mil. Two ounces is 70 micrometres, three is 105, four is 140, six is 210 and ten is 350. Going from 2 oz to 4 oz doubles the copper mass, and going from 1 oz to 4 oz multiplies it by four, which is the step where process settings stop transferring from the standard line.
What etch takes off a 4 oz trace
Etch removes copper down and sideways at the same time. The ratio of depth to lateral undercut is the etch factor, and on a cupric chloride line running well it sits near 1 to 1.5. At 1 oz that means about 35 micrometres of undercut per side on the way down, near 1.4 mil, which is why 1 oz artwork usually carries around 1 mil of compensation per side. At 4 oz the depth is 140 micrometres and the lateral loss per side is the same order, up to 5.5 mil, so a 6 mil top line can finish close to 1 mil at the base if nothing is added back.
The consequence is practical. A heavy copper trace is a trapezoid with a hot spot, because current density at the base is higher than at the top and the cross section is smaller than the drawing says. That is why the published minimum at 2 oz is 5.5 mil line and space on our FR-4 line, and why a 4 oz request with 4 mil lines comes back as a wider geometry or a refusal instead of a quiet acceptance.
What it does to the soldering profile
The copper is the thermal mass. A 4 oz plane pulls heat out of a joint faster than a 1 oz plane, and a 2 mm heavy copper board holds more heat than a 1 mm board, so the profile that works on a standard card leaves the heavy area cold. Our 4 oz builds run a soak at 150 to 180 C for 90 to 120 seconds, a ramp under 2 C per second, a peak of 235 to 245 C at a thermocouple on the heavy area, and 45 to 90 seconds above 217 C, which is the SAC305 liquidus. The thermocouple goes on the heavy area, not on the panel edge where the profile always looks healthy.
Wave soldering moves the same way. Preheat has to bring the top side of a 140 micrometre plane to 100 C or more before the wave arrives, otherwise the pad and the barrel pull solder away and the joint fills short. A selectively soldered connector on a 4 oz board often needs a longer dwell and a higher iron setpoint than the identical connector on a 1 oz board, and the difference is the copper, not the operator.
Three places builds go wrong
Specifying 4 oz with fine lines. The copper has to go somewhere. A geometry that asks for 4 mil lines in 4 oz forces the etcher to over-etch and the base of the trace disappears. The 2 oz rule of 5.5 mil, and the wider geometry at 4 oz, are etch facts rather than a commercial preference.
Running the standard profile. The board passes inspection, the joints look a little dull, and the customer sees voids or opens after the first thermal cycle. A profile developed on 1 oz does not transfer. The fix is a thermocouple in the heavy area and a soak long enough to equalise the panel, not a higher peak that scorches the mask.
Forgetting the mask and the legend. Solder mask over a 140 micrometre trace is thin at the trace edge and thick over the laminate, so a 1.5 mil opening that is clean on 1 oz can bridge or lift on 4 oz, and legend printed across the step of a heavy trace sits on a slope. The mask and legend call-outs belong in the same conversation as the copper weight.
How we hold it
SUPERB PCB quotes heavy copper as a package rather than a number: base copper 0.5 to 4 oz on inner layers as standard, up to 6 oz inner and 10 oz outer on the extended line, plating of at least 20 micrometres in the barrel, and a panel up to 622 by 1092 mm so a power stage does not have to be split across two boards. Etch compensation is written on the fabrication drawing and stated as an allowance per side, and the first article goes to cross section: copper on the trace top, at the base and in the barrel, measured instead of assumed.
Assembly runs the heavy boards with the profile developed for the copper weight, and the mask is measured after cure rather than judged by eye. The finished requirements are on heavy copper PCB, the process side on heavy copper solutions, and the 2 oz to 10 oz power stage cases are in heavy copper for power stages.
What to send with the question
The copper weight per layer, the current each trace carries and the allowed temperature rise, the minimum line and space, the board thickness and layer count, the soldering method, and whether the heavy copper sits on an outer layer or an inner one. With those six the answer is a geometry, an etch allowance and a profile, and the quote does not come back after the first panel has been scrapped.