Turnkey PCBA Assembly Service
Product Specifications
Turnkey PCBA assembly from one supplier: PCB fabrication, BOM sourcing, SMT and through-hole assembly, X-ray, test and box build for RF, defense and medical boards.

Turnkey PCBA means one purchase order covers the whole board: the bare PCB is fabricated, every component on the BOM is procured against the approved manufacturer list, the board is assembled, tested and packed, and one shipment arrives at your dock. There is no split responsibility between a board house, a parts broker and an assembly shop. When a build fails, there is one party to answer for it.
Superb Automation runs turnkey programs for RF and microwave products where the component mix is narrow but unforgiving: PTFE and Rogers laminates, GaN and GaAs power devices, phase-matched coax launches, shielded cans and press-fit connectors. BOM procurement is handled by the same team that has sourced RF and microwave parts for 25 years, so an obsolete synthesizer or a long-lead LNA is resolved before it stops the line, not after.
We assemble to your released design. Schematic capture, circuit design and layout changes stay with you; what we return is manufacturability feedback on the files you send, a build that matches those files, and test data that proves it.
Key Specifications
| Item | Capability |
|---|---|
| Board type | Rigid, rigid-flex, RF/microwave, heavy copper, HDI |
| Layer count | 2 to 68 layers |
| Base material | FR-4, high-Tg FR-4, Rogers, Taconic, PTFE, mixed dielectric |
| Minimum line / space | 0.0125 mm on advanced builds |
| Assembly types | SMT, through-hole, mixed technology, press-fit, selective solder |
| Component range | 01005 chip to fine-pitch BGA, QFN, LGA and RF connectors |
| BGA / fine pitch | X-ray inspection on every BGA and bottom-terminated package |
| Inspection | AOI, X-ray, first-article inspection, IPC-A-610 Class 2 and Class 3 |
| Test | ICT, flying probe, functional test, RF test with VNA and spectrum analysis |
| Traceability | Lot and date-code records per board, serialisation on request |
| Volume | Prototype quantities through volume production, one line |
| Documentation in | Gerber, BOM with MPN and manufacturer, centroid, assembly drawing, test spec |
Where Turnkey Builds Usually Fail
Turnkey programs fail in the gap between the BOM and the physical board, not on the placement machine. A BOM that lists a generic value instead of a full orderable part number will be bought as whatever the distributor has that week. A second-source part with a different pinout will fit the footprint and fail the test. A laminate change from Rogers to FR-4 will shift the impedance and quietly degrade return loss.
On RF boards the margin is smaller still. Solder volume on a QFN ground paddle changes thermal resistance. Shield can placement shifts filter response. A connector pressed 0.1 mm off nominal changes launch impedance. These are the points where a turnkey supplier either catches the problem at DFM review or ships it to the customer.
Test Strategy
Test is defined before assembly, not after. For a turnkey build the sequence is normally: bare board electrical test at the fab, SPI after paste print, AOI after reflow, X-ray on BGA and QFN, then in-circuit or functional test at board level. RF boards add a VNA sweep for insertion loss, return loss and isolation, plus a power sweep for compression where a PA is fitted.
Test fixtures are quoted separately because they follow the test specification, not the board count. A functional fixture built for one program is normally reused across builds, so the cost is amortised after the first order.
PCB Fabrication Requirements
RF and high-speed turnkey builds put the fabrication and the assembly in the same tolerance chain. Impedance control has to be held at the fab to plus or minus 10 percent, because the assembly cannot correct it afterwards. Press-fit holes are drilled to plus or minus 0.05 mm and the finished hole size is checked after plating. Heavy copper builds above 3 oz need a different etch and resist process. When fabrication and assembly are quoted by different suppliers, these tolerances get lost between the two quotes.
Applications
RF front-end modules — multi-stage LNAs, filters and switches on PTFE laminate, with shield cans and phase-matched traces.
Radar T/R modules — high-layer-count boards with many identical channels, where channel-to-channel phase consistency is the acceptance criterion.
SATCOM up and down converters — mixed RF and digital assembly, tight shielding, connectorised housings.
Test and measurement instruments — low-volume, high-mix builds with calibrated RF paths and strict serialisation.
Medical RF chains — MRI and ablation front ends, where lot traceability and process records are part of the regulatory file.
Defense communication radios — ruggedised assemblies with conformal coating, press-fit backplanes and extended temperature validation.
Why Superb Automation
- 25 years of component sourcing behind every turnkey quote, including obsolete and end-of-life RF parts that distributors no longer list.
- One purchase order covering board fabrication, material procurement, assembly, test and box build, with one party accountable for the result.
- RF and microwave process experience: PTFE and Rogers laminates, mixed dielectric stack-ups, shielding and phase-matched routing.
- X-ray and AOI on every build, with first-article inspection and IPC-A-610 Class 2 and Class 3 acceptance.
- Manufacturability feedback on the files you release, returned as a written list before the first board is made.
- Lot and date-code traceability retained per build, so a field failure can be traced back to the material batch.