The number that decides whether a defense board survives is not the g level in the test plan. It is the g level at the middle of the board. Ground materiel is commonly screened to 40 g 11 ms half sine functional shock and 75 g 6 ms crash hazard under MIL-STD-810H Method 516.8, on top of random vibration near 0.04 g squared per Hz from 10 to 1,000 Hz, which integrates to roughly 5 to 8 g rms for one hour per axis on three axes. A board with its first mode at 200 Hz and a Q of 15 turns 5 g rms into about 75 g at the centre.
That is the whole argument in two sentences: the specification is written at the mounting interface, and the assembly lives somewhere else.
Why the board amplifies the input
A 200 by 150 mm board at 1.6 mm on four standoffs behaves as a plate, and its first mode lands near 150 to 250 Hz, which is inside the transportation band. A Q of 10 to 20 is normal for FR-4 at room temperature. A short span or a stiffener moves the mode up and usually lowers the amplification, but it also moves the mode toward the 500 Hz to 2,000 Hz band where the fixture and the harness start to behave badly.
Component mass is what converts acceleration into force on a joint. A 10 g heatsink at 75 g is 7.3 N, and on four small solder joints that is a load no 0402 termination was qualified for. A 30 g connector with a harness tied at 50 mm is worse, because the harness adds mass at the worst possible place and the tie point becomes a pivot.
Fatigue follows a power law. Solder joint life scales roughly with the inverse square of the strain range, so halving the strain buys about four times the cycles, and a stiffener that halves the board deflection is worth more than any coating. Transportation alone is 10 to 100 million cycles at theseing on bandwidth, which is where the damage is done before the board ever flies.
What the standard asks for, and what it leaves to you
Method 514.8 Procedure I covers general vibration for equipment carried as secured cargo or used on a vehicle: a sine sweep to find resonances, then either a resonance dwell or a random profile per category, applied on three axes, typically one hour per axis. Method 516.8 covers shock: 20 g 11 ms for flight materiel functional test, 40 g 11 ms for ground materiel functional test, and 75 g 6 ms for the ground materiel crash hazard.
What it leaves to you is the mounting. The standard tests the item as it is mounted in the fixture. If the fixture clamps the board on all four edges while the product holds it on four standoffs, the test measures a different board with a different first mode and a different answer.
Three mistakes that show up after the first shake
One accelerometer, on the fixture. Without a response channel bonded to the board, the report proves the shaker met its profile and says nothing about what the assembly saw. Two channels on the board, one at the centre and one near a heavy part, cost almost nothing and change the conclusion.
One axis. Transport, gunfire and launch each have three. Boards that pass vertical often fail transverse because the stiffener only works in one direction.
Torque and thread locking left to the line without a number. An M3 screw into aluminium at 0.6 N m and at 1.2 N m are two different joints: one keeps preload for the life of the unit and the other loses it in the first hour of vibration. The value belongs on the work instruction next to the driver setting, not in a verbal handover.
A fourth, quieter one: treating conformal coating as a mechanical fix. Coating protects against humidity and contamination. It does not hold a 10 g heatsink, and staking does.
What SUPERB Assembly puts into a build that will be shaken
Heavy parts are staked with an approved adhesive, and the adhesive lot and cure record go with the serial number. Torque values and thread locking are written on the work instruction, and the driver is set to them rather than to feel. Press-fit connectors are placed with the hole tolerance and insertion force recorded, because a press-fit pin that loses retention under vibration starts as a plating or hole tolerance problem.
Inspection is IPC-A-610 Class 3 with 3D SPI, 3D AOI, and X-ray and CT to IPC-7095 with voids under 5 percent on thermal pads. The laminate side is available up to 68 layers with heavy copper to 6 oz inner and 10 oz outer for power sections, board thickness from 0.6 to 3.2 mm on the standard line, and back drilled stubs at 0.25 mm or less where the same board also carries high speed nets. The build routes are described on defense and radar PCBA, the laminate window on high reliability PCB, and the assembly flow on turnkey PCBA assembly.
The qualification test itself runs at the customer laboratory or an accredited one. What leaves here is a build that matches the mounting in that fixture, with the standing hardware, the staking and the torque record already in place.
What to send
Send the vibration profile with its frequency range, level and duration per axis, the shock pulse and the number of drops or pulses, the mounting points and hardware, the board size and thickness, the heaviest components with their mass, the connectors and how the harness is tied, and whether the assembly must operate during the test. That is enough to say whether the build needs a stiffener, a change of standoff spacing or a heavier board before the first panel is ordered.