A mixed technology board carries a reflowed top side and a handful of through hole parts that cannot see a solder wave. A connector with a plastic body, a relay, a shield can or a terminal block with a long pin will not survive a wave, and hand soldering the same joints gives a result that depends on who held the iron.
Selective soldering sits between the two. A programmed nozzle visits each joint, deposits flux, preheats locally and holds the solder for a set time. The result is a joint that looks like a wave joint with a repeatable record behind it, and the cost is a program per board plus the time the nozzle spends travelling between joints.
Whether that trade is worth it depends on the board, not the process name: where it earns its place, which four variables decide the joint, and what the package has to state.
Where wave soldering stops working
A wave is fast because it solders everything at once, and that is also its limit. Masking a wave for a fine pitch part, a press fit pin or a connector with an open body is a manual job, and every mask is a chance for a bridge or an unwetted joint. Large thermal mass on one side of the board pulls heat away and leaves a cold joint on the other. A tall component shadows the joints behind it. A board with parts on both sides cannot be waved at all without a carrier.
Hand soldering solves the access problem and creates a consistency problem. Two operators on the same joint give two fillets. Selective soldering keeps the access of hand work and adds the record of a machine.
What the process actually controls
Four variables decide the joint, and all four are set in the program rather than by the operator on the day.
| Variable | What it decides | How it fails when it is wrong |
|---|---|---|
| Flux deposition | Whether the oxide on the pin and the barrel is removed before the solder arrives | Dry joint or a fillet that climbs the pin but never enters the barrel |
| Preheat | Whether the board and the pin reach a temperature the solder can wet in the dwell time | Cold joint on a heavy ground plane, or thermal shock on a large ceramic part |
| Nozzle path and dwell | How long the solder contacts the joint and from which side | Short dwell leaves an incomplete fillet, long dwell lifts the laminate or scorches the flux |
| Nitrogen and wave height | Whether the solder surface stays clean and reaches the barrel from below | Dross on the joint, or a barrel that fills halfway and opens in thermal cycling |
The program is per board and per side. Two products that share a connector still need their own program, because the thermal mass around that connector is different and the dwell that fills a barrel on one board leaves a cold joint on the other.
Selective, wave or hand: which one fits
| Board situation | Route that fits | Reason |
|---|---|---|
| Through hole parts concentrated on one edge, plastic bodies, no fine pitch | Wave with a carrier | One pass, and the mask job stays small |
| Mixed pins spread across the board, heat sensitive parts nearby, fine pitch connectors | Selective | Local heat and a programmed path, no full board immersion |
| Two or three pins, large terminals, low volume | Hand with a controlled iron and a fillet standard | The program and the fixture cost more than the joints are worth |
| Press fit pins | Neither, it is a press operation | Solder is not part of the joint |
How a selective run is set up here
The run starts from the drawing, not from the last product that looked similar. Fixture, nozzle selection, flux type and the nitrogen setting are fixed at first article, and the profile is confirmed with a thermocouple on the actual board before the lot runs. Wave work where the board allows it uses the wave machine described under wave soldering, and the reflow side of the same board is covered under nitrogen reflow soldering.
SUPERB PCBA runs selective and wave work behind a flow of seventeen steps with ten quality stations, held to IPC-A-610 Class 2 and Class 3, under ISO 9001 and ISO 13485 for medical work. Assembly covers seven SMT lines with 01005 placement, 3D SPI after print, 3D AOI after reflow, DIP AOI after the through hole operation and X-ray read to IPC-7095 with voiding under five percent. Every through hole joint is judged on fillet, barrel fill and wetting angle, and the station sequence sits under PCBA quality control.
Barrel fill is the number buyers ask about, and the answer is a percentage from the drawing rather than a house default. A Class 3 build usually calls for full fill on a plated barrel, and that requirement drives the dwell and the preheat, so it belongs in the package before the program is written.
What the build package must state
Five items, and a missing one either stops the run or turns into an assumption nobody wrote down.
| Item | What we need |
|---|---|
| Which joints are in scope | The through hole list and any pin the drawing wants left unsoldered |
| Fill and fillet standard | Barrel fill percentage, fillet shape and the class the lot is judged to |
| Heat sensitive parts | Parts within 10 mm of a nozzle path, with their maximum temperature and time |
| Flux and residue rule | Whether a no clean flux is accepted, and whether the board is washed after the operation |
| Masking and keep out | Areas that must stay free of flux and solder, including any open contact |
Selective soldering questions
Can you run selective soldering on a board that is already fully reflowed?
Yes, and that is the normal case. The reflowed side is protected by the fixture and by the fact that the nozzle heats a small area. What has to be checked is the secondary reflow risk: a heavy through hole part close to a fine pitch device can push that device above its reflow temperature if the preheat is set too high.
Is nitrogen necessary?
For a lead free joint on a plated barrel, it removes the variable that most often causes a partial fill. Without it the solder surface oxidises during the dwell and the barrel fills less than the fillet suggests. The nitrogen is measured in the program, not assumed from the supply pressure.
How do you verify a barrel that cannot be seen?
By X-ray on the first article and on a sample per lot, read against the fill requirement on the drawing, and by cross section when the customer wants a destructive check on a coupon. A visual check of the fillet says nothing about the barrel, which is where an open joint starts.
Next step
Send the Gerber set, the through hole list, the fill standard and the parts that sit close to the nozzle path, or send the board with the connector that is giving trouble. The reply returns the route, the fixture and program items, the nitrogen and dwell call, and a price with the tooling shown as its own line.