A serial number sequence is a promise that every unit built can be found again. When the sequence jumps, the promise breaks at exactly the point where it matters. A unit comes back from the field carrying a number that sits inside a gap, and nobody can say whether it was built, scrapped, or never existed at all.
The gap itself is rarely the problem. What decides the outcome is whether the gap is explained, bounded and signed, so that a unit inside it can be accounted for years later. That is what a break record is for, and it takes less than an hour to write when the facts are still fresh.
Why a gap in the sequence costs more than it looks
Serial numbers do three jobs: identify a unit in the field, bound a recall, and answer an auditor. A gap damages all three.
For a recall, the boundary is the number range. A gap that cannot be explained has to be included, which expands the recall to units never shipped and possibly never built. Explained, the recall stops at the last real unit.
For a customer audit, the question is unit level and specific: which material lot went into serial 4471. If 4,455 to 4,470 are missing from the records with no note, the auditor has to assume the record set is incomplete, and every other answer becomes a claim rather than a fact.
What causes a break in the sequence
| Cause | What it looks like on the floor | What the evidence proves |
|---|---|---|
| Damaged label stock | Blank labels at the end of a roll, or a run of labels that will not take print | Numbers were consumed by the printer and never applied to a unit |
| Printer fault | Partial or unreadable code on an otherwise good label | The number exists on a label that was destroyed, not on a unit |
| Scrap after labelling | Units rejected at inspection after the label went on | The number was issued and the unit was destroyed, with a scrap record to match |
| Rework and relabel | A label removed during repair and replaced | One unit may carry two numbers unless the first is voided in writing |
| Split or cancelled build | A block of labels issued to a work order that was cut short | Numbers were reserved but never consumed, and the remainder has to be voided |
| Counter reset | A software or database reset that restarts the counter | The most serious case, because two units can carry the same number |
What a break record has to contain
Eight fields answer the questions that arrive later. The record is written once, when the gap is found, and signed by whoever can see the physical evidence.
| Field | What it has to say | Why it decides the outcome |
|---|---|---|
| Last number before the gap | The last unit that was built, tested and recorded | Sets the closed end of the range |
| First number after the gap | The first unit that resumed the sequence | Sets the open end, so the gap has a size |
| Quantity in the gap | The count of numbers missing, not an estimate | An estimate turns into an open question at audit |
| Cause | One of the six causes above, named at the station where it happened | Separates a consumed number from a duplicate |
| Whether any unit carries a gap number | Yes, no, or unknown, with the check that was done | The single field that decides if a recall has to widen |
| Evidence held | Label roll, printer log, inspection log, scrap record | Makes the record checkable rather than asserted |
| Disposition of the numbers | Voided, never issued, or issued and scrapped | Prevents the same block being reissued later |
| Approval | Name, role, date, and the next review if units surface | A gap signed by production alone is a note, not a control |
Void the numbers, do not reuse them
The strong rule is that a number, once printed, is never issued to a different unit. Reuse is what turns a paperwork gap into two units with one identity, and it is the failure that cannot be repaired later because the field data is already wrong.
A replacement label for a recorded unit carries the original number with a suffix, so the unit still matches its test record. A block printed and never used is voided against the work order, so a later reprint does not quietly consume it.
How SUPERB PCBA keeps unit numbers aligned
Units are numbered against the work order and the kit they were built from, so number, material lot and test result stay in one record. Incoming material is counted by X-ray and checked for part number, quantity, date code and maker markings before release, which is what makes the kit record trustworthy.
Builds run on seven SMT lines with 01005 placement, 3D SPI after print, 3D AOI after reflow and X-ray to IPC-7095 with voiding under five percent, through a seventeen step flow with ten QC stations under IPC-A-610 Class 2 and Class 3. The quality system is ISO 9001, with ISO 13485 for medical work, and components carry a 730 day warranty from receipt. Test results are recorded against the unit number rather than the batch, so a returned unit traces back to its kit and its inspection result.
Where a unit is scrapped or reworked after numbering, the number is voided with the reason and the station, and the lot record carries the count of voids.
Serial number break record questions
Is a break record needed if no unit was built in the gap?
Yes, and it is the easiest version to write. The point of the record is to prove that the numbers were printed and destroyed rather than issued to an unrecorded unit. Without it, an auditor has no way to tell the two apart.
How long should the record be kept?
As long as the unit level records for that product, which for medical and telecom equipment is the service life plus the contract period. The wider record chain is set out under component traceability report.
What if the gap is found months later?
Write it with the date it was found and the date it happened, and state plainly that the physical evidence is no longer available. A late record that says what can no longer be checked is worth more than no record, because it stops the next person from assuming the range is complete. The outgoing side of the same question is covered under PCBA outgoing quality report.
Next step
Send the serial number range you are holding open, the lot it belongs to and whatever label or printer records still exist. The reply returns which of the eight fields can be closed from the evidence, which numbers have to be voided rather than explained, and the wording for the lot file. For the test records behind the numbers, see PCBA test coverage strategy.