A PCBA price arrives as one number and is argued about as one number. That is why the argument rarely reaches a conclusion. The number is a sum of lines with completely different behaviour: some are fixed per order, some scale with quantity, some are set by the board and some by the parts. Until the lines are separated, no one can tell whether a lower price is a better deal or a smaller scope.
The breakdown below is the one SUPERB PCBA quotes against. It is not a price list, because the values move with the build. It is the shape of the number, which is what a buyer needs in order to ask the right question.
The seven lines inside a PCBA price
Bare board. Priced per square metre of panel, so layer count, material and finish decide most of it. A four layer FR-4 board and an eight layer high speed board at the same outline are not comparable, and neither is a Rogers board against FR-4 at the same layer count.
Material. Priced per line of the BOM, quantity broken at the reel. This is the line that moves most between two quotes, and the one where a difference usually means a different brand, date code position or channel rather than a different margin.
Tooling and setup. Stencil, solder paste and print program, placement program, reflow profile, test fixture where the build needs one. Fixed per order, so it dominates a small quantity and vanishes on a large one.
Placement and assembly labour. Priced per placement and per operation, with a setup charge per line change. Double sided builds pay it twice, and a build with a wave solder or selective solder step pays for the extra operation.
Test. Either a fixed cost for a fixture plus a low cost per unit, or a higher cost per unit with no fixture. Which is cheaper depends on quantity, which is the subject of the separate comparison between the two stations.
Coating, potting and conformal work. Material plus masking labour plus cure, priced per unit, with the masking often the larger half on a board with many keep clear areas.
Packing and freight. Per carton, per pallet, per destination, with the export documents as their own line on a first shipment to a new country.
PCBA cost breakdown by behaviour
| Line | Behaves as | What moves it | What a buyer can change |
|---|---|---|---|
| Bare board | Per unit, set by panel | Layers, material, finish, panel utilisation, quantity | Panel arrangement, finish choice, order quantity |
| Material | Per unit, set by BOM | Brand, tolerance, package, order quantity, date code rule | Approved alternates, quantity break, brand flexibility |
| Tooling and setup | Fixed per order | Stencil count, program count, fixture, line changes | Number of variants, whether a fixture is needed |
| Placement | Per placement | Placement count, fine pitch share, double sided, mixed technology | Part consolidation before release |
| Test | Mixed | Coverage level, station, fixture, cycle time | Coverage scope, station choice, sample against full test |
| Coating | Per unit plus masking | Area, keep clear count, material, cure route | Keep clear list, material family |
| Packing and freight | Per shipment | Carton count, mode, destination, terms | Consolidation, terms, schedule |
Why the unit price falls with quantity, and where it stops
The fall is not one curve. Tooling is divided across the quantity, so the first doubling does most of the work. Material falls in steps, at the reel and at the box, not smoothly. Labour falls only where the line amortises setup over more units, and it stops falling once the build runs at line rate.
A quote for ten and a quote for a thousand differ by a factor that surprises buyers, and a quote for a thousand and one for five thousand differ by very little. Past that point the remaining cost is material, and material does not care how many boards you build.
Where a buyer has real leverage
The biggest lever is the BOM before release. Two 0.1 uF capacitors in different packages cost two setups and two line items; one package for both removes a feeder and a setup. Consolidating values, removing a part that exists only for a build option, and moving a rare value to a common one each remove work from the line.
The second lever is the alternate list. A BOM that names one brand and one package leaves nothing to buy when that part is on fourteen week lead. An approved alternate on the long lead lines protects the schedule without a written deviation later.
The third is the quantity break. Asking for the price at the quantity the program actually needs, rather than at a round number, often lands on a better break. Reels are 3,000 or 5,000 pieces and the price steps at those points, not at 1,000.
The methods we use to work those levers are set out under reducing component cost, and the information that has to be on the table for a quote to be accurate at all is under quote checklist.
What the lines do not include
Freight terms matter as much as the price. An FOB price and a delivered price differ by freight, insurance and duty, and two quotes compared without that are not comparable.
Engineering changes after release are their own cost. A change after the stencil is cut pays for a new stencil and a new setup, and a change after the first articles pays for a re-test as well.
Scope also moves the number. A quote that assumes functional test and one that assumes none are different products, and the lower one is not a better price. Our quotes state the scope on the face of the document, and scope is agreed before the order rather than after BOM sourcing starts.
Questions buyers ask
Is there a margin on the material?
The material line is a purchase price plus the cost of buying, holding and administrating it. Asking for the material at cost and paying the handling as a separate line gives the same total in most cases.
Why did the price change between the quote and the order?
Almost always one of three things: a part moved in price, the BOM changed, or the quantity crossed a break. Our quotes state the validity date and name the parts that are volatile.
Can we see the breakdown of our own quote?
Yes. The lines are already separated on the quote we send: bare board, material, tooling, placement, test, coating and packing. A buyer who wants the placement count behind a line can ask for it.
Does a higher price mean a better build?
Not by itself. A difference is only meaningful against the scope behind it: test coverage, inspection level, class of work, material brand, traceability. Two quotes at different prices with the same scope are worth comparing.
Next step
Send the BOM, the Gerber set and the quantity for the first build plus the annual figure, and say which lines you expect to move. The reply returns a quote with the seven lines separated, the quantity breaks marked, the volatile parts named, and the tooling as its own line so the effect of quantity is visible before you commit.