The bracket goes on, the screw bottoms in the hole, and the head stands 1.2 mm proud of the board. The drawing said counterbore 3.4 mm, and the panel came back with a 3.4 mm hole drilled straight through. Nothing was drilled wrong. The drawing never said how deep, or what had to remain underneath.
Both features are decided entirely by the callout. On a 1.6 mm board a recess of the wrong depth either leaves the head proud or takes out so much laminate that the screw crushes the pad under it.
What the two features are
A counterbore is a flat bottomed recess: a hole of one diameter cut to a set depth, so a socket head screw, a standoff boss or a connector body sits below the surface. The wall is vertical and the floor is flat. A countersink is a cone cut into the top of a hole, so a flat head screw finishes flush with the surface. The angle matches the screw, most often 82, 90 or 100 degrees.
The counterbore clears a volume, the countersink clears an angle. Mixing them up is the most common note error on a mechanical drawing.
Which one the board needs
| Application | Feature | What it has to clear | What the drawing must state |
|---|---|---|---|
| Chassis or enclosure mounting | Counterbore | Screw head and washer, with the board clamped flat | Diameter, depth, remaining wall under the floor, non plated |
| Heat sink or bracket standoff | Counterbore | Standoff boss and the torque of the screw | Diameter, depth, flatness of the floor, distance to the nearest trace |
| Flush panel screw | Countersink | Flat head screw, head angle | Angle, major diameter, depth, finish inside the cone |
| Connector or display recess | Counterbore, sometimes stepped | Body height and the lead bend radius | Both diameters, depth of each step, tolerance on the step |
| Guide pin or dowel relief | Counterbore | Pin head sitting below the mating face | Diameter, depth, position against the datum |
Where a recess sits close to a via or a trace, the drawing also has to give the keep out, or the panel comes back with the recess where it fits rather than where it was drawn.
Numbers that belong on the drawing
A counterbore needs three numbers: diameter, depth, and the tolerance on the depth. The third is the one that gets dropped, and the depth is exactly the value that drifts across a panel, because the drill program works from the surface and the surface moves with copper and plating. On a thin board it is better to call out the remaining wall under the floor than the depth, because the remaining wall is what the screw load sees and what the laminate has to survive.
A countersink needs the angle, the major diameter at the surface, and the depth, plus the finish inside the cone. A cone cut after surface finish exposes bare copper at the rim if the hole is plated, so the note has to say whether the cone may break through the plating or the head must sit on a plated ring.
Plated or non plated
Most counterbores are non plated. Plating inside the recess adds thickness at the floor, changes the depth, and in a small recess it builds a lip that stops the screw seating. Where the recess also carries ground, the usual answer is a separate ground pad beside it, or a plated ring at the rim that the head contacts before it bottoms.
A countersink on a plated hole is different. The cone is cut into the plating, so copper is exposed at the cone face. That suits a ground screw and fails where the recess has to stay solderable or hold a low contact resistance over time.
The process order that keeps the recess usable
- Inner layers, lamination, drilling and plating to the required copper weight.
- Surface finish, so the finish covers the through holes and the pads.
- Counterbore and countersink cut in the mechanical stage, from the finished surface.
- Deburr and clean, with the recess checked for laminate dust and plating flakes.
- Electrical test, then a first article section that measures depth and remaining wall.
Cut the counterbore before plating and the recess gets plated. Cut the countersink before finish and the cone is covered with whatever the finish is, which changes the seating angle of the screw. Cut either one after assembly and the debris lands on the components.
Where a recess goes wrong
Depth drift across a panel comes first, at roughly the same value as the panel thickness variation, which is why the remaining wall has to be checked at the corners and not only at the centre. Second is breakout into inner copper: a counterbore whose floor lands on a power plane shorts the screw to that plane, and that shows up only at assembly. Third is the burr at the rim, which lifts a heat sink off the board and turns a thermal problem into a contact resistance problem. Fourth is mask left inside the recess, which cracks and drops flakes into the assembly.
How SUPERB PCBA handles a recess
Boards are produced to print at the PCB end in Jiangsu and Zhuhai. The published mechanical envelope covers hole sizes from 0.15 to 6.35 mm, hole position within 0.075 mm, non plated hole size within 0.05 mm, board thickness 0.6 to 3.2 mm on the standard line and 0.1 to 12 mm at the extended end, profile within 0.15 mm, and trace to board edge of 0.20 mm or more, which is the number that decides how close a recess can sit to a trace. Layer count runs 1 to 20 on the FR-4 line and up to 68 on the high layer line.
Every recess is checked against the drawing before release, and the first article ships with a section that measures the floor and the remaining wall. Assembly then works from the same outline, so a bracket built around a 1.2 mm recess is not fitted to a board with 0.9 mm of laminate left under it. The full mechanical list is on the FR-4 process parameters page, and hole quality checks are described under hole inspection.
Questions buyers ask
Can a counterbore be cut through a copper plane?
Yes, if the plane is cleared around the recess and the drawing says so. Otherwise the screw shorts to that plane.
Does a countersink change the hole size?
No. The through hole keeps its diameter and the cone is cut above it. What changes is the surface diameter, and that is the number the screw head covers.
Can the depth be adjusted after the first article?
Yes, before the panels are drilled. Depth is a program value, so a change on the first article is cheap and a change after the lot is drilled is a new lot.
Next step
Send the Gerber set with the mechanical layer marked up: which recesses, which diameters, which depths or remaining walls, plated or not, and the datum the position is measured from. The reply comes back with a drill and rout drawing for approval and the first article section that proves the floor before the rest of the lot is cut.