Contact Us

PCB Board Thickness Tolerance

PCB Board Thickness Tolerance

The purchase order says 1.6 mm. The receiving bench measures 1.52 mm at one corner and 1.63 mm at the other, the connector lead no longer reaches the far row of pads, and the argument starts about whether the board is out of tolerance or the measurement is.

Neither side is wrong yet. Board thickness is a finished number that includes copper, plating and mask, measured at points nobody wrote down, against a band that was copied from a template. Getting it right is a matter of three decisions: what the number covers, where it is measured, and how tight it has to be for the parts that clamp the board.

What the finished number includes

Finished thickness is the distance through the whole stack: laminate, inner copper, outer copper, plating in the holes and on the surface, and solder mask over the traces. On a 1.6 mm board with 1 OZ outer copper and 20 micrometres of plating, those layers add up to a few hundredths of a millimetre, which is inside a ten percent band but not inside a two percent one.

The same board measured over a copper pour and measured over bare laminate can differ by the copper and mask above the laminate. That is why a callout without a measuring point produces two honest measurements that disagree.

The bands buyers work to

Nominal thicknessBandWhat it means in practiceWhere it needs tightening
Below 1.0 mmPlus or minus 0.10 mmA fixed band, because ten percent of 0.8 mm is too tight to hold on a pressCard guides and flexible hinges that set a slot height
1.0 mm and abovePlus or minus 10 percentPlus or minus 0.16 mm on a 1.6 mm boardPress-fit connectors, edge connectors with a fixed throat
3.2 mm and aboveBy agreement from the stack upCopper weight dominates the total on thick power boardsBusbar joints and heavy copper boards with 6 OZ inner layers
Controlled impedance stackSet by the impedance, not the thicknessLayer spacing drives the trace width, so the two move togetherRF and high speed boards where a thickness change moves impedance

The standard line runs 0.6 to 3.2 mm, and the extended end reaches 0.1 to 12 mm, with the band above applied at both ends. A nominal outside the standard range is quoted against the stack, not against a template.

What moves the finished number

Copper weight comes first. A board with 4 OZ inner layers and 10 OZ on the outer surfaces carries a lot of metal, and the laminate between them compresses less than a 1 OZ stack, so the same 1.6 mm nominal builds to a slightly different finished value. Plating adds to the outer surface and inside every hole. Lamination pressure and the number of press cycles, up to seven on a complex stack, each leave a small residue. Solder mask adds a few micrometres, enough to matter on a callout written to two decimal places.

Why the number matters downstream

Three things clamp the board and each one cares about a different part of the number. A card guide or chassis slot cares about the maximum, because a board over the slot height will not enter. An edge connector with a fixed throat cares about the minimum and the maximum, because the contact force depends on the gap. A press-fit connector cares about the hole depth relative to the pin length, so a board on the thin side leaves the pin standing proud and a board on the thick side bottoms the pin before the shoulder seats.

Impedance is the quieter one. On a controlled stack the layer spacing is part of the trace geometry, so a board that builds 4 percent thin shifts the impedance by roughly the same order. The tolerance that governs impedance is covered under RF and microwave PCB capability, where the number is plus or minus 5 percent, and plus or minus 2 percent on critical runs.

How to write the callout

  1. State the nominal and the band as two numbers, for example 1.60 mm plus or minus 0.16 mm, rather than as a percentage alone.
  2. State where it is measured: over copper, over laminate, or at four points along the edge and at the centre.
  3. State which limit matters. Where a slot clamps the board, give a maximum. Where a connector sets the gap, give both.
  4. Leave the band alone on a controlled impedance stack, and tell the board house which layer pair sets the impedance, so the press target is set from that pair.

A callout written this way survives incoming inspection, because the inspector measures the same place against the same band. A callout that says 1.6 mm and nothing else gets measured wherever the caliper lands.

How SUPERB PCBA holds the number

Boards are built to print at the PCB end in Jiangsu and Zhuhai, with the press target set from the stack up rather than from a nominal figure. The published band is plus or minus 0.10 mm below 1.0 mm and plus or minus 10 percent from 1.0 mm up, over a standard range of 0.6 to 3.2 mm and an extended range of 0.1 to 12 mm. Warpage is held to 0.75 percent or less for boards that go through surface mount, and to 0.5 percent or less on HDI and rigid flex, because thickness variation and warp arrive together on a thin panel.

Layer count runs 1 to 20 on the FR-4 line and up to 68 on the high layer line, with impedance held to plus or minus 5 percent and back drill depth within 0.05 mm where a high speed layer pair needs it. The full table is on the FR-4 process parameters page, and the acceptance limits for warp are set out under bow and twist acceptance limits.

Questions buyers ask

Is a 1.6 mm board exactly 1.6 mm thick?

No. It is 1.6 mm nominal, and the finished value sits inside the band, which is plus or minus 10 percent on the standard line.

Does plating count towards the finished thickness?

Yes, and so does mask. That is why the callout has to say whether the measurement is taken over copper or over laminate.

Can the band be held to plus or minus 5 percent?

On a simple stack and by agreement, yes. It is quoted against the stack up and the measuring method, and it is not the default on a panel with mixed copper weights.

Next step

Send the Gerber set with the stack up and the three decisions written down: nominal plus band, measuring points, and which limit the connector or the slot actually needs. The reply comes back with the stack up marked for press target, the thickness and warp values that will be reported per lot, and a first article measurement at the points named in the callout.