Contact Us
  • Home
  • BLOG
  • Why Do 0201 Capacitors Tombstone During Reflow?

Why Do 0201 Capacitors Tombstone During Reflow?

A 0201 tombstone is a wetting race that one end wins. The two terminations almost never melt and wet at the same instant, and at this size the part is light enough that the difference stands it up before the second end can pull it back down. The cause is in the print, the pad, or the copper around the pad, and almost never in the component.

The arithmetic explains why such a small difference is enough. A 0201 measures 0.6 by 0.3 by 0.3 mm and holds about 0.32 mg of ceramic, so its own weight is 3.2 microNewtons. The wetting force on one termination is the surface tension of SAC305 at 250 C, about 0.55 N/m, times a wetted perimeter of roughly 1.2 mm, which gives about 660 microNewtons. The wetting force is 200 times the weight, so an imbalance of half a percent between the two ends already equals the weight of the component, and the pivot sits at the other termination 0.3 mm away. On a 0402 the same imbalance is a quarter as effective, which is why the defect appears when a line moves down a case size and not before.

The print is the first suspect

Paste volume has to match at both ends, and the stencil decides that before the squeegee moves. A 0.28 mm square aperture in 0.10 mm foil has 0.0784 mm2 of area and 0.112 mm2 of wall, which is an area ratio of 0.70 and releases cleanly. The same aperture in 0.12 mm foil gives 0.58, below the 0.66 floor, and now the paste stays in the aperture on one pad and transfers on the other depending on gasketing, blade angle and how the aperture sits relative to the pad. A 20 percent pad to pad volume difference is enough to tombstone a 0201, and 20 percent is inside the noise of a press that is not monitored.

Two more print variables matter at this size. Nano coated or electropolished apertures release consistently, where a plain laser cut aperture releases differently at the start of a print stroke than at the end. And squeegee pressure that is set once for a board with 0402 and large parts is usually too high for the 0201 area, which scoops paste out of the small apertures and leaves a thin print on one side of the board and a full one on the other.

The pad and the copper around it

Pad geometry sets where the molten paste pulls. A pad that is 0.1 mm longer than the termination gives the paste a longer lever on that end, and the part rotates toward the longer pad. Pad asymmetry between the two ends is worse than a pad that is uniformly too large, because the pull is direct and repeatable.

Copper balance matters for a different reason: heat. One pad connected to a plane and the other to a trace means the plane side stays cooler and melts later. The trace side wets first, pulls, and by the time the plane side is liquid the part is already standing. The same happens with a via in pad on one end only, or with a thermal relief on one side and a solid connection on the other. The test is simple and worth doing once per board: run a thermal camera over the footprint during reflow and read the two pads. A difference of a few degrees at the melting point is a repeatable tombstone.

The profile and the placement

Fast ramp makes the difference between the two ends larger, and a soak of 150 to 180 C for 60 to 90 seconds equalises the footprint before the paste melts. Nitrogen below 500 ppm widens the wetting margin and reduces the sensitivity to oxide on one termination, which is often the difference between a 0.3 percent and a 0.05 percent defect rate on the same print. Peak temperature belongs to the paste data sheet, not to the upper limit of the oven: a peak well above the recommendation burns the flux on the side that heats first and removes the wetting force that was supposed to pull the part down.

Placement offset is the last contributor. At 0.05 mm of offset on a 0.6 mm part the centre of mass sits over one pad, and the surface tension then works with gravity instead of against it. Placement accuracy of plus or minus 0.05 mm is the floor for 0201, and the offset should be read on the first article rather than assumed from the machine specification.

Three habits that make it worse

Adding paste to help it wet. More paste means more force, more slump and a longer lever, and the defect rate goes up. The correction is less paste and equal paste, never more.

Changing the part and keeping the print. The same case size with a different termination finish wets at a different rate, and a part with a nickel barrier behaves differently from one with a tin finish. A substitution approved on dimensions is not approved on wetting.

Running 0201 on a 0402 process window. Aperture size, foil thickness, squeegee setting and soak time all scale with the case size. When a line moves down a size, three settings change together, and a defect that appears on the first lot is usually the process window rather than the material.

What SUPERB controls on a 0201 build

Every print is measured in 3D, with volume, height and offset per pad, so a 20 percent pad to pad difference is caught before the board reaches the oven instead of after. Stencil thickness and aperture are set per case size, apertures are nano coated, squeegee pressure and speed are set for the fine pitch area, and the profile is developed on the actual board with a soak that equalises the footprint. Reflow runs in 12 zones with nitrogen under 500 ppm, placement is specified to plus or minus 0.05 mm with capability down to 01005, and AOI follows reflow with X-ray on the joints that optics cannot see. Final inspection is to IPC-A-610 Class 2 or Class 3 as the product requires, with first article comparison against CAD data.

The print and placement scope is on turnkey PCBA assembly. Where the cause turns out to be a plane connection or a via in pad on one end, the board side is covered on multilayer PCB and high reliability PCB, because a balanced stack and symmetric thermal spokes remove the thermal half of the problem before assembly starts.

What to send with the question

Board thickness and copper weight per layer, which pads sit on a plane and which on a trace, the pad dimensions for the 0201, stencil thickness and aperture, paste type and maker, the reflow profile, placement offset from the first article, and the defect rate with its position on the panel. Position matters more than the rate: tombstones that cluster on one edge of the panel point at the print stroke, and tombstones that cluster near a connector point at heat.

Need a quote or a review of your build against these limits? pcba@superb-tech.com · WhatsApp +86 133 9608 1443