Fifteen micrometres over the top of a trace, with a floor of five at the thinnest point. That is our published figure, 15 micrometres plus or minus 10, and it is measured on the copper, not on the bare laminate beside it. Put the minimum over conductor on the drawing and the number becomes enforceable; leave it as a board average and it is not.
The wide band is not sloppy control, it is geometry. Liquid photoimageable ink is pushed across the panel by a squeegee, it settles in the gap between traces to a depth set by the mesh and the solids content, and it drains off the top of every trace while the solvent flashes. The same print therefore reads thick in the gap and thin on the copper, and a 70 micrometre 2 oz trace drains more ink down its sidewalls than a 35 micrometre 1 oz trace does.
Why the trace top is always the thin end
Look at where the ink has to go. Between two traces it fills a channel and its only escape is downward through the solvent. On top of a trace it has a free edge on both sides. Surface tension pulls the ink over those edges during levelling. On a 0.20 mm trace with 0.20 mm spacing the channel therefore reads deeper than the trace top, from one pass of the same screen.
That is also why the 2 oz case is tighter than the arithmetic suggests. Seventy micrometres of copper leaves a 70 micrometre deep trench between traces. Ink that measures 15 micrometres on the trace top cannot fill a trench that deep, so the dam between two heavy traces is a slope rather than a wall, and the width that survives at the bottom of the trench is what insulates. Our published 2 oz minimum line and space is 5.5 mil on both counts, against 3.0 mil at 1 oz, and most of that gap is the dam, not the trace.
Measurement matters as much as the target. A magnetic or eddy current gauge reads the ink over copper cleanly; over laminate the same gauge reads the copper underneath if the ink is thin. A cross section is the only way to see both the trace top and the channel, and it is the reading that should go on a first article report. IPC-SM-840 qualifies the material, adhesion, insulation resistance after humidity and resistance to cleaning solvents, and it does not set a thickness, which is why the drawing has to.
What the thickness actually buys
Coverage of the copper edge. An etch defined trace has a slope, and the mask has to wrap that slope. At 5 micrometres the edge is barely covered, and after a reflow or two the ink lifts along the copper.
Surface insulation resistance. A dense grid under a thin print reads low on a humidity test. If the assembly is going to run no-clean, the mask is the last barrier and it should not be the thin one.
Impedance. This is the part that gets missed. Solder mask has a dielectric constant of about 3.5 against 1.0 for air, and 15 micrometres of it over a 50 ohm microstrip pulls the number down by 2 to 4 ohm. Our impedance window is plus or minus 5 percent, which is 2.5 ohm each side of 50, so a calculation done in air can spend the whole budget before the board is etched. Ask for the field solve with the mask included, and ask which thickness was assumed.
Dam width. Thicker ink bridges a narrow dam and slumps into the opening, thinner ink leaves the copper exposed at the pad edge. Green holds a 3.5 mil dam, white and black need 5 mil because the pigment load raises the viscosity and the film thickness, and other colours sit at 4 mil. On our capability page the floor is 50 micrometres, and that floor is a green ink number at 1 oz.
Three ways the callout goes wrong
Specifying an average instead of a minimum over conductor. "Mask 25 micrometres" is read by most shops as a target for the print, and a panel that averages 25 can read 10 on a trace top. Write both: nominal and minimum over copper, and state that the reading is taken on the trace, not in the gap.
Solving impedance in air. The 2 to 4 ohm shift is larger than the tolerance band most customers quote, and it moves with ink colour as well as thickness, because a white or black print is thicker. A 50 ohm target that ignores the mask is a 46 to 48 ohm board, and it will measure that way on the coupon.
Copying a green ink rule onto another colour. A 50 micrometre dam with white ink on 2 oz copper is not a process that exists. Either widen the dam or change the colour, and decide it before the artwork is released, because both changes touch the pad geometry.
What SUPERB PCB holds on mask
Published: ink thickness on a trace 15 micrometres plus or minus 10, minimum opening 1.5 mil, minimum dam 3.5 mil in green, 5 mil in white and black, 4 mil in other colours, 50 micrometres on the capability page, mask dielectric constant 3.5 as a reference figure, trace width tolerance plus or minus 20 percent, 2 oz minimum line and space 5.5 mil, and impedance plus or minus 5 percent with plus or minus 2 percent on critical nets. These sit on the FR-4 process parameters page and the capability page.
The honest boundary: the 15 micrometre figure is a print result, not a guarantee that every square millimetre of a dense panel reads it. On a board with 0.10 mm spacing and 2 oz copper, we quote the dam at the wider end and say so before the panel starts. Where a customer needs both a 50 micrometre dam and 2 oz, the answer is usually to move the tight spacing to an inner layer, which is a stack decision, not an ink decision.
Mask thickness also sets the tent. A covered via relies on the ink bridging the hole, and a print that is thin over copper is thin over the tent as well. Vias that must stay flat for paste release are filled and capped instead, which is a different process and a different number, and the choice between the two is set out in via-in-pad filling types.
What to send with the drawing
The ink colour, the minimum thickness over conductor and where it is measured, the narrowest dam on the board and its copper weight, whether the nets are impedance controlled and whether the field solve included the mask at the thickness you expect, the finest line and space, whether any via is tented, and the cleaning or no-clean route the assembly will use. Seven lines, and they settle the print before the first panel, which is the only moment when changing it costs nothing.