A lot arrives with a finish date fourteen months old. The purchase order asked for ENIG and nothing about age, the boards look clean, and nobody knows whether they will wet. Two weeks later the first panel shows non wetting on half the ground pads and the argument starts about who pays. Shelf life is not a property of the board. It is an agreement about a finish, a package and a storage condition, and unless the order states all three, there is nothing to hold anyone to.
What actually changes while a board sits on a shelf
Three mechanisms do the damage. The finish oxidises, the layer between finish and copper grows, and contamination settles on the surface. Sulfur from cardboard and rubber, humidity, and heat all accelerate the first and last. The middle one is why thin finishes age faster than thick ones.
| Finish | Typical shelf life | What degrades | Storage note |
|---|---|---|---|
| OSP | 6 months | Copper oxide grows through the film, and each reflow consumes some of it | Sealed with desiccant, bake with care, it is not a finish that tolerates repeated heating |
| Lead-free HASL | 12 months | An oxide skin forms on an already uneven surface | Robust to storage and bake, but flatness limits what it can carry |
| Immersion silver | 6 to 12 months | Sulfur tarnish, which looks alarming and may still solder | Sulfur free interleave paper, sealed bag, no cardboard contact |
| Immersion tin | 6 months | Copper tin intermetallic consumes the tin layer | Cool and sealed, and whisker risk reviewed for the application |
| ENIG | 12 months | Nickel oxidises through the porous gold, and a poor deposit can go to black pad | Dry storage, avoid repeated baking, check nickel thickness on arrival |
| ENEPIG | 12 months | Slower diffusion because the palladium layer blocks it | Same as ENIG, with wire bonding as the reason to pay for it |
The dates are industry practice, not physics. A sealed ENIG lot stored cool and dry often solders well past twelve months, and an OSP lot that sat open in a humid room can fail at four. That is why the outgoing report should carry the finish date and the packing date as two separate fields: they are rarely the same day, and only one of them starts the clock.
Storage rules that do the real work
- A moisture barrier bag, not a plain poly bag. Aluminium foil laminate, desiccant and a humidity indicator card. IPC-1602 covers handling, packing and storage, and it is the document to quote when a supplier says the packaging is standard.
- Temperature and humidity. 5 to 30 C and below 70 percent relative humidity, with no condensation cycle. A warehouse that swings between cold nights and warm days condenses water on the boards inside a sealed bag.
- Nothing sulfur bearing in contact. Cardboard, foam, rubber bands and some labels are the usual culprits on silver and OSP.
- First in, first out, with the date visible. A bag without a legible finish date will be opened last, which is the opposite of what is needed.
- Opened bag, running clock. Mark the open date on the bag. A board that has spent three weeks open on a humid floor is not the same board that came in.
Baking: what it fixes and what it costs
Baking drives out moisture, and moisture is real. A board that absorbed water will outgas at reflow, which shows as blisters, measling and sometimes delamination on thick multilayer and rigid-flex builds. For that problem a bake is the answer: a common starting point is 120 C for four to eight hours on thin boards, longer and ramped more slowly on thick builds, agreed with the board supplier rather than assumed.
The cost is on the other side of the ledger. Heat grows oxide on OSP, ages immersion silver and speeds intermetallic growth on immersion tin. So baking has two outcomes, and the sequence matters: bake, assemble inside a defined window, then re-bag the rest. Baking an OSP lot as a routine step before every build removes the very film you paid for.
Settling a disputed lot with a solderability test
J-STD-003 covers solderability of printed boards, with a dip and look method for through holes and pads and a wetting balance method for critical work. A report is only useful if it states the flux type and activity, the alloy, the solder temperature, the immersion time and depth, whether a steam ageing precondition was applied, and the acceptance criteria. Without those five or six fields, "it passed" is an opinion.
Steam ageing has been used for decades as a quick stand in for shelf life, with eight hours often quoted as roughly a year. That equivalence was established on tin lead systems. On lead free finishes, use steam ageing to compare a suspect lot against a known good control from the same supplier, and treat the result as a comparison rather than a calendar.
How SUPERB handles incoming boards
SUPERB Assembly checks incoming boards against IPC-6012 and the purchase order before release to the line: finish, thickness, date code, packaging condition, panel count, and the flatness clause where the drawing carries one. Boards stay sealed until the line calls for them, and the SMT floor runs at 22 plus or minus 3 C and 45 to 65 percent relative humidity in an ISO 8 area under ANSI/ESD S20.20, so an opened stack does not sit in wet air. Where a lot is old, or a bag was opened months earlier, the choice between a bake and a solderability test is made and recorded rather than assumed, and the finished assembly is inspected to IPC-A-610 Class 2 or Class 3.
- FR-4 process parameters: finish options, thickness ranges and the tolerances a purchase order can quote.
- PCB testing guide: the inspection and test steps a build passes through before shipment.
- Environmental reliability testing: thermal cycling and the tests that expose a marginal finish.
Frequently asked questions
Can an expired lot still be used?
Often yes, if a sample passes solderability and the customer accepts the deviation in writing. The test has to be on the actual lot, with the flux and alloy that production will use, not on a coupon from the board supplier's qualification run.
Does nitrogen storage help?
It slows oxidation at the surface, and for high value boards in long storage it is worth considering. The sealed bag with desiccant does most of the work for a fraction of the cost, and it also controls moisture, which nitrogen alone does not.
Which date starts the shelf life, the board or the bag?
The finish date, which is when the surface treatment was completed. The packing date is usually later and only tells you when the board was bagged. Ask for both on the label, and for the shelf life statement to name the finish and the storage condition it assumes.
Next step
Send the purchase order clause and the finish you need. The quotation states the finish date and shelf life that will be recorded on the outgoing report, the packaging used, and for old or long stored material, the solderability evidence that comes with the lot before it reaches your line.