A motorsport body control module survives four things: a load dump that reaches about 100 V on a 12 V system, tens of amps switched into inductive loads a few centimetres away, vibration a road car never sees, and a heat soak that begins the moment the engine stops. The logic almost never fails. What fails is the power path, the connector, and the solder joint that joins them.
That list is also the order of cost. Protection is a component choice, current is copper and joints, vibration and water are process and housing.
The supply is not 12 V
ISO 16750-2 load dump on a 12 V system runs from 79 to 101 V, ten pulses a minute apart, with a source impedance of 0.5 to 4 ohms and a decay that can last 400 ms. A 24 V system goes to 151 and up to 202 V. With a clamp at 30 V and a 0.5 ohm source, one pulse puts something near 400 joules through the clamp; with a 4 ohm source it is nearer 50 joules. Ten of those inside ten minutes is a thermal problem as much as a voltage problem, and it is why a load dump device on a motorsport board is chosen for energy and die size rather than for a headline wattage.
The rest of the list is quieter and just as common. Overvoltage at 18 V for an hour with the regulator failed. A 24 V jump start for 60 seconds. Reverse polarity at minus 14 V. And the switching transients from the loads themselves: a 100 mH relay coil at 1 A stores 50 mJ, and released without a clamp it appears at hundreds of volts on the driver. The clamp belongs at the FET, within a few millimetres of the drain, not at the fuse box where the harness inductance sits between it and the device.
Current is a copper and joint problem
A 30 A output on 2 oz copper, 10 mm wide and 50 mm long, dissipates about 0.11 W in the trace. Tks harmless: one 0.3 mm via with 25 micrometre plating and 1.6 mm of barrel is roughly 1.2 milliohms, and at 30 A that is over a watt in a single hole. A high current output needs a field of vias, a copper bar, or a terminal that carries the current into the plane without crossing a barrel. Copper weight helps: 2 oz is the working baseline and the upper limit here is 6 oz inner and 10 oz outer, which is the point where a 30 A path stops being a routing puzzle.
The harness is the other half of the decision. Twenty metres of 2.5 square millimetre copper weighs 450 g; the same run in 0.75 square millimetre weighs 134 g. One kilogram of copper buys 45 m at 2.5 square millimetre. Every load that moves from a dash switch to a module output trades a long power wire for a short one, and that arithmetic is what really sizes the module.
Heat, vibration, water
ISO 16750-4 puts an engine compartment part between minus 40 and plus 125 degrees, and a cockpit part between minus 40 and plus 85. The number that catches people is the soak after a stop: coolant flow ends, the block radiates into the bay, and a module that ran at 90 degrees sees 20 to 30 degrees more for ten minutes. Solder joints and electrolytic capacitors age on that curve, not on the running temperature.
Vibration is a fatigue problem. A random profile from 10 to 2000 Hz with a resonance in the housing can be amplified tenfold at the mounting point, and a 100 g connector on a 1.6 mm board then pulls at a joint with tens of newtons several million times. Underfill, a bracket that supports the connector body rather than the board, and a joint filleted on both sides decide whether that survives.
Water arrives as a pressure washer, not as rain. A connector rated IP67 is a claim about the interface, and the interface is where a leak starts: a seal compressed once and reconnected at the track is no longer the seal that was tested. A pressure equalisation vent keeps the housing from pumping moist air through that seal on every heat cycle, and potting or selective coating has to stop short of the contacts.
Three mistakes that come back as returns
Sizing protection from the nominal rail. A 30 V clamp on a 12 V rail reads as generous until the pulse energy is checked against the die. The specification that matters is clamping voltage at the stated pulse current for ten pulses, plus the derating at 125 degrees, not the standoff voltage on the first page.
Coating over the connector. Conformal coating on a contact surface is an intermittent fault waiting for a season of vibration. Masking the contacts, the mating faces and any pressure sensor port belongs in the coating programme, not in a note on a drawing.
Qualifying with a hand built first article. Hand soldered heavy copper joints, a machined bracket and a hand applied coating never repeat on a line, and the difference between them and the production process is exactly the failure mode being qualified. The first article has to come off the line that will build the rest.
How SUPERB supports a motorsport BCM build
SUPERB PCB covers the power side: heavy copper to 6 oz inner and 10 oz outer, up to 68 layers, 0.05 mm lines, impedance control, and a surface finish that survives the thermal cycles a coated board sees. SUPERB Assembly places and solders the module on seven SMT lines, 01005 up to 57 mm, with 3D SPI before reflow, 3D AOI after it, X-ray and CT to IPC-7095 with voids under 5 percent on thermal pads, twelve zone nitrogen reflow below 500 ppm oxygen, selective coating and potting with masking held to the drawing, then ICT, flying probe and functional test on a fixture built around the loads the module actually drives.
Components come through 7,000 plus authorized channels with a 730 day warranty, which matters on a board where a counterfeit FET is a fire risk rather than a yield number. The quality system is ISO 9001, with ISO 13485 for medical work. Builds are build-to-print from your Gerber, BOM and assembly drawing, with no engineering fee in the quotation.
The module family is described on the body control module PCBA page, the power path on heavy copper PCB, and what changes at 4 oz and above in the heavy copper article. The rest of the vehicle electronics work sits under automotive PCBA.
What to send
Send the load list with steady and inrush current per output, the transient specification the module has to meet, the connector part numbers, the mounting and the temperature class, plus the Gerber and BOM. The quotation then reflects copper weight and test fixture, which are the two items that move most between a 10 A module and a 60 A one.