IPC-A-610 is the document an inspector uses to accept or reject an assembled board. Class 3 in that document is not a vague call for "better workmanship": it is a set of specific, photographable criteria for wetting, fillet shape, voiding, placement and cleanliness, and the difference from Class 2 is often a matter of a tenth of a millimetre.
This page covers what actually changes at Class 3, and where assemblers most often get caught.
1. What the document is, and what it is not
IPC-A-610 covers the acceptability of electronic assemblies: solder joints, component placement, damage, cleanliness, coating and marking. It does not tell an assembler how to run the process, that is J-STD-001. The two are used together: J-STD-001 defines the process requirements, IPC-A-610 defines what the result must look like.
Both documents have Class 1, 2 and 3 criteria, and the assembly class is independent of the bare board class in IPC-6012. A Class 3 bare board can legitimately be assembled to Class 2 criteria if the drawing says so, and the reverse.
2. Solder fillets and wetting
Class 2 accepts a fillet with a concave shape and wetting around most of the joint, with some allowance for minor imperfections that do not affect reliability.
Class 3 requires a properly wetted fillet around the entire joint, with the toe, heel and sides wetted, and a fillet profile that shows correct wetting angle rather than a rounded ball sitting on the pad. No dewetting, no non-wetting, no icicles, no solder balls that exceed the size criteria.
The practical difference on the line: a joint that looks fine to an untrained eye at Class 2 can be a reject at Class 3 because the heel is not wetted, which is the part of the joint that carries the thermal cycling stress.
3. Component placement and orientation
Class 3 tightens the side overhang, end overhang and terminal overlap limits, and is stricter about damage to the component body and terminations. It also constrains how much the part can be rotated before it is a defect rather than a process indicator.
For fine-pitch and area array parts, the placement tolerance is effectively set by the stencil and the placement machine, so the Class 3 requirement has to be designed into the process, not inspected in at the end.
4. BGA and area array devices
The visual criteria in IPC-A-610 cover what can be seen: alignment, collapse, solder ball presence at the perimeter. What cannot be seen, the voiding under the package, is judged against IPC-7095 practice and the customer's specification, typically with X-ray.
Class 3 programs usually specify a void limit per ball and a total void area limit, plus a rule for voids that merge. A common specification is 25 percent void area per ball with no single void crossing the ball diameter, but the number that applies is the one in the drawing.
X-ray alone does not prove a joint. It proves the presence of solder. For Class 3 area array work, add dye-and-pry or cross-section on the first article, and keep the images with the lot record.
5. Through-hole and press-fit
Class 3 requires vertical fill and a fillet on both sides for most through-hole joints, with tighter limits on pin protrusion and on the allowance for voids in the barrel. Press-fit connectors are judged on the hole size and the press-in force record rather than on solder appearance, and both should be on the drawing.
6. Cleanliness and residues
Class 3 programs usually carry an ionic contamination limit and a requirement for no visible residue that could cause corrosion or leakage. No-clean flux is acceptable only if the process is qualified for it and the residue is benign at the specified limits.
The trap is a board that passes visual and fails surface insulation resistance after coating. Cleanliness has to be measured, not assumed from the flux label.
7. Coating, marking and damage
Conformal coating coverage, thickness and cure are specified separately (IPC-CC-830 for the material). Class 3 requires coverage of the areas the drawing defines with no voids over the joints, and cure verified by test rather than by touch.
Damage criteria also tighten: a scratch, a nicked conductor or a lifted pad that is acceptable at Class 2 may be a reject at Class 3.
8. What the assembler needs from the customer
The assembly class, stated per feature if it varies. The void criteria for area array parts. The cleanliness limit and the test method. The coating coverage drawing. The acceptance authority for rework and for deviations.
Without those, the assembler will apply its default, which is usually Class 2 with a Class 3 eye on the visible joints. That is not a criticism; it is what "IPC-A-610 Class 3" alone in a purchase order actually authorises.
9. Where Class 3 assembly programs fail
Thermal profile not matched to the paste and the board: joints that look right and have a cold fillet under the toe. Stencil aperture and area ratio wrong for fine pitch: inconsistent paste volume, intermittent opens. Insufficient cleaning after a water-soluble process: residue under the components that only shows up in humidity testing. Rework without a qualified procedure: a hand-reworked joint that passes visual and fails thermal cycling.
All four are process issues. All four are invisible in a final visual inspection at Class 2 criteria.
10. Summary
IPC-A-610 Class 3 is a set of specific visual and measured criteria, most of which are decided by the process rather than the inspector. Specify the class, the void limits, the cleanliness method and the coating drawing, and require the first article evidence. Then the inspection is a confirmation, not a discovery.
Related reading
- IPC-TM-650 Test Methods: Which Test Proves What
- IPC-6012 vs MIL-PRF-31032: Which Specification Applies
- J-STD-001 vs IPC-A-610: Process Standard or Product Standard?
- IPC-6012 Class 3 Compliance Checklist
- IPC Class 2 vs Class 3: What Actually Changes
- High reliability PCB manufacturing
- PCBA assembly services
