Contact Us
  • Home
  • PCB
  • Rigid-Flex PCB for Robot Joints and Wrist Assemblies

Rigid-Flex PCB for Robot Joints and Wrist Assemblies

Rigid-flex PCB for robot joints and wrists. Polyimide flex layers, dynamic bend design, controlled impedance, replaces cable harnesses in moving joints.
quote now

Product Specifications

Product Overview

A rigid-flex board replaces the cable harness that runs through a moving joint. The rigid sections carry the connectors and the components, and the flex section bends with the joint, thousands of times a day, without a connector in the middle.

The design is mechanical as much as electrical. Bend radius, copper grain direction, coverlay openings and the number of flex layers decide the fatigue life; a board that works on the bench can fail in a month if the bend line crosses a plated through-hole.

We build rigid-flex from 4 to 8 layers with 1 mil to 2 mil polyimide, adhesiveless laminates for dynamic applications, and bookbinder or flying-tail constructions depending on how the flex exits the rigid section.

Key Specifications

Layer count4 to 8 total, 2 to 4 flex layers
Flex materialPolyimide, 1 mil / 2 mil, adhesiveless
Bend typeDynamic, up to 10 million cycles at 3 mm radius
Min line / space4 / 4 mil on flex
CoverlayPolyimide coverlay or photoimageable
StiffenerFR-4 or polyimide, 0.2 to 1.0 mm
Impedance± 10% on controlled pairs
Board thickness0.2 mm flex, 0.8 to 1.6 mm rigid
Surface finishENIG
StandardsIPC-6013 Class 2 / Class 3
InspectionCross-section, bend test, microsection
AssemblySMT on rigid sections only

Stack-up and Construction

A joint interconnect typically uses a 6-layer build: two flex layers in the middle, one rigid layer on each side, bonded with no-flow prepreg in the bend area so the flex stays free.

Dynamic bend requires rolled annealed copper rather than electrodeposited copper, and the bend line is kept away from plated through-holes and from any coverlay opening.

Where the flex leaves the rigid section, a bookbinder construction keeps the bend radius controlled; a flying tail is cheaper but puts more strain on the transition.

Manufacturing Challenges

  • Plated through-holes in the bend area are the primary failure point; the design keeps all holes at least 1 mm outside the bend zone.
  • Coverlay registration on fine lines is harder than solder mask; a shifted opening exposes copper that oxidises and cracks under repeated bending.
  • The rigid-flex transition traps prepreg flow; excess resin stiffens the bend and shortens the fatigue life.
  • Assembly reflow heats the whole board, and the flex section must be supported so it does not sag or take a permanent set.

Inspection and Quality

Flex quality is proven by bending, not only by sectioning:

  • Cross-section at the rigid-flex transition on each lot.
  • Bend test on a coupon to the specified radius and cycle count, with resistance monitored.
  • Adhesion test between coverlay and copper.
  • Impedance measurement on controlled pairs before assembly.
  • Visual inspection of the bend zone under magnification for coverlay lift or copper cracks.

Applications

  • Robot wrist and finger joints with limited space
  • Humanoid arms that route power and signal through a rotating joint
  • End effectors that change tools frequently
  • Camera modules on articulated arms
  • Surgical and laboratory robots with sterile cable paths
  • Wearable exoskeleton joints

Why Superb Automation

  1. Stack-up and copper weight reviewed against the current and thermal requirement before the first panel is released.
  2. Etch compensation and plating thickness controlled per lot, with coupons from every panel measured and recorded.
  3. Impedance and copper thickness verified on test coupons, not only on the first article.
  4. Heavy copper and mixed construction builds held on one schedule with the assembly line, so bare boards and assemblies do not slip against each other.
  5. Inspection reports, X-ray and cross-section images supplied with the lot on request.
  6. One quotation covering fabrication, tooling and any assembly step on the same drawing set.