Vision and CSI Camera Interface Board PCBA for Robots
Product Specifications
Product Overview
A vision board takes several camera modules and brings their MIPI CSI-2 lanes back to the compute module, adds clock and reset control per port, and supplies clean power to each sensor without injecting switching noise into the lanes.
The electrical work is dominated by signal integrity. Each CSI-2 lane runs at up to 2.5 Gbps per lane, the pairs must stay matched within a few picoseconds, and the connectors on the camera side are often micro-coax or fine-pitch FPC, which adds impedance discontinuities.
We build the board on 8 to 10 layers with controlled impedance on every lane, ground stitching between pairs, and per-port power filtering placed at the connector rather than at the regulator.
Key Specifications
| Layer count | 8 to 10 layers, HDI |
|---|---|
| Base material | FR-4 low loss, Tg 170 °C |
| Camera ports | 4 to 8, MIPI CSI-2 |
| Lane speed | Up to 2.5 Gbps per lane |
| Impedance | 100 ohm differential ± 8% |
| Skew | Intra-pair under 5 ps, inter-pair under 50 ps |
| Connectors | Fine-pitch FPC or micro-coax |
| Power | Per-port LDO, 1.8 V / 2.8 V, low noise |
| Control | I2C per port, reset and trigger lines |
| Operating temperature | -20 to +70 °C |
| Coating | None on connectors, selective on logic |
| Test coverage | 100% ICT, lane continuity, camera loop test |
PCBA Assembly Challenges
- Fine-pitch FPC connectors have a large pad capacitance relative to the lane impedance; the escape routing has to compensate or the eye closes at the connector.
- Each camera port needs its own power filter, and placing all filters at the regulator instead of the connector couples noise between ports.
- Trigger and sync lines run next to high-speed lanes and pick up crosstalk; they need spacing and, where possible, a ground guard.
- Camera flex cables are fragile and often replaced in the field, so the connector retention and strain relief matter as much as the electrical design.
Test Strategy
Every port is exercised with a real sensor, not only with a continuity test:
- In-circuit test including lane continuity and the I2C buses.
- Camera loop test on every port with a reference sensor at full resolution.
- Eye scan on the CSI lanes with the flex cable fitted.
- Power rail noise measurement at the connector under load.
- Thermal check at 70 °C ambient with all ports streaming.
PCB Manufacturing Difficulty
HDI with 3 mil lines is needed to escape from the fine-pitch connectors; the microvia-in-pad process must be filled and capped or the connector pads will have voids.
Impedance on CSI pairs depends on the prepreg thickness next to the signal layer; the stack-up is frozen before routing so the coupons match the design.
Ground stitching between pairs has to be dense enough to control crosstalk without cutting the reference plane under the connector.
Applications
- Humanoid robots with head and hand cameras
- Mobile robots with 360-degree camera rings
- Robot arms with wrist-mounted inspection cameras
- Teleoperation kits that stream multiple views
- Warehouse robots with depth and RGB fusion
- Research platforms that swap sensor types between experiments
Why Superb Automation
- Engineering review before tooling: stack-up, copper weight, creepage and assembly sequence are checked against the drawing before the first panel is released.
- PCB fabrication and PCBA assembly held to one schedule, so the bare board and the assembly do not slip against each other.
- Incoming component inspection with X-ray and XRF on reels, plus traceability records per lot.
- Selective conformal coating, potting and staking available in the same build, not subcontracted to a third party.
- Functional test fixtures built to your specification, with DC, digital and boundary-scan coverage reported per unit.
- Quotation from one BOM and one drawing set, with DFM feedback returned before you commit to a build.