Joint Servo Drive Board PCBA for 48 V Robot Actuators
Product Specifications
Product Overview
Every robot joint has one of these boards: a three-phase inverter, a current sensor, an encoder interface and a field-oriented control loop, packed into a diameter that fits inside the actuator housing.
The constraints are electrical and mechanical at the same time. Peak current of 60 A in a 40 mm circle means the copper has to be thick, the MOSFETs close to the phases, and the current sense placed where switching noise does not corrupt the loop.
We build the drive on 6 layers with 3 oz outer copper, thermal vias under the power stage, and the encoder interface on an isolated or differential input depending on cable length. The board is tested with a real motor, not a resistive load.
Key Specifications
| Layer count | 6 layers, 1.2 to 1.6 mm |
|---|---|
| Copper weight | 3 oz outer, 2 oz inner |
| Bus voltage | 24 to 60 V DC |
| Peak phase current | 60 A for 2 s, design dependent |
| Continuous current | 20 A at 40 °C ambient |
| Power stage | GaN half bridge or low Rds(on) MOSFET |
| Control | FOC, 20 kHz current loop, 1 kHz position loop |
| Encoder | Magnetic absolute, BiSS-C or SPI, differential |
| Sensing | Phase current shunt or Hall, 12-bit ADC |
| Operating temperature | -20 to +85 °C at the board |
| Coating | Selective polyurethane on the power stage |
| Test coverage | 100% ICT, motor spin test, thermal soak |
PCBA Assembly Challenges
- Current sense placement decides loop noise: a shunt on the source of a switching device sees common-mode steps of 48 V in 10 ns, and the amplifier needs enough CMRR to reject them.
- Thermal vias under the power stage must be filled; a void under a 3 mm pad raises the junction temperature by 15 to 25 K at rated current.
- The encoder cable runs through a moving joint and picks up motor switching noise, so the interface needs differential signalling and common-mode filtering.
- Board outline is dictated by the actuator housing, not by layout convenience, which forces the power stage and the encoder connector onto opposite edges.
Test Strategy
Each board drives a reference motor through a full motion profile before it is accepted:
- In-circuit test including the phase outputs and the current sense chain.
- Static phase resistance and shoot-through check with the power stage disabled.
- Motor spin test: torque command sweep, current loop bandwidth and position error recorded.
- Thermal soak at 85 °C board temperature for 30 minutes at 50% load.
- Encoder interface test with a reference magnetic encoder at 4000 rpm equivalent.
PCB Manufacturing Difficulty
3 oz copper with 6 mil spacing at the phase nodes leaves little room for the gate return; we route the power stage on the outer layers and keep the inner layers for gate and sense.
The circular outline means panel utilisation is poor; we nest boards with shared tooling strips and accept the yield penalty rather than change the outline.
Selective coating on the power stage must avoid the connector and the test pads, and it must not bridge the gap between the phase pads.
Applications
- Humanoid robot arms and legs with integrated actuators
- Quadruped robots with 12 joints on a 48 V bus
- Collaborative robot joints that need torque sensing
- Exoskeleton actuators with high peak torque
- AGV steering and lift drives
- Laboratory test rigs that characterise actuator dynamics
Why Superb Automation
- Engineering review before tooling: stack-up, copper weight, creepage and assembly sequence are checked against the drawing before the first panel is released.
- PCB fabrication and PCBA assembly held to one schedule, so the bare board and the assembly do not slip against each other.
- Incoming component inspection with X-ray and XRF on reels, plus traceability records per lot.
- Selective conformal coating, potting and staking available in the same build, not subcontracted to a third party.
- Functional test fixtures built to your specification, with DC, digital and boundary-scan coverage reported per unit.
- Quotation from one BOM and one drawing set, with DFM feedback returned before you commit to a build.